John Deere 410b 510c Backhoe Operator Manual
John Deere 510B 510C Backhoe Repair Technical Manual
John Deere 410B To 510C Backhoe Loaders Repair Technical Manual
Cover: 410B, 410C, 510B 510C (TM1469)
John Deere 410B, 410C, 410D, 510C Backhoe Loaders Technical Manual
Complete Table of Contents
Manual Introduction
- Specifications & Serial Number Locations
- General Maintenance & Lubrication Schedules
- Fluid Capacities & Recommendations
- Tire Pressures & Torque Specifications
Group 01 – Power Train
Backhoe Loader
- Engine (John Deere Diesel): Disassembly, Assembly, Crankshaft, Cylinder Block, Pistons & Rings, Valves, Fuel System (Injection Pump, Nozzles), Cooling System, Lubrication System.
- Torque Converter: Testing, Removal, Disassembly/Assembly.
- Transmission (Manual Reverser / Powershift): Servicing, Control Valves, Clutches, Shafts, Gears.
- Drive Shafts & Universal Joints: Service and Replacement.
- Front Axle & Drive: Differential, Axle Shafts, Steering Knuckles, Hubs.
- Rear Axle & Differential: Disassembly, Bearings, Gears, Brakes.
- Parking Brake: Adjustment and Service.
Group 02 – Hydraulic Systems
- Main Hydraulic System: Gear Pump, Control Valves, Relief Valves, Lines.
- Loader Hydraulics: Lift and Bucket Circuits, Cylinder Rebuilding.
- Backhoe Hydraulics: Swing, Boom, Stick, and Bucket Circuits; Piston Pumps (where applicable), Stabilizer Cylinders.
- Steering Hydraulic System: Orbitrol Steering Unit, Cylinder Repair.
- Brake Hydraulic System: Master/Slave Cylinders.
Group 03 – Frame and Equipment
- Frame & Mounting: Loader Frame, Backhoe Mounting.
- Loader Assembly: Bucket, Linkage, Cylinder Pins & Bushings.
- Backhoe Assembly: Boom, Dipper Stick, Bucket, Pivot Pins, Bushings, Wear Strips.
- Stabilizers & Outriggers: Legs, Pads, Cylinders.
John Deere 410B To 510C Backhoe Loaders Service Technical Manual
Group 04 – Electrical System
- Wiring Diagrams (Complete Schematics for each model).
- Starting System: Battery, Starter, Solenoid.
- Charging System: Alternator, Regulator.
- Instrument Panel: Gauges, Switches, Sensors.
- Lighting Circuit: Headlights, Warning Lights.
Group 05 – Miscellaneous
- Operator’s Cab (ROPS): Seats, Controls.
- Heating & Air Conditioning (if equipped): Compressor, Condenser, Evaporator.
- Attachments: Options and related hydraulics.
Group 10 – Testing & Troubleshooting
- Diagnostic Procedures: Performance Tests for Hydraulics and Power Train.
- Symptom-Based Troubleshooting:
- Engine Won’t Start or Runs Poorly
- Low Hydraulic Power or Slow Operation
- Transmission Slips or No Movement
- Electrical System Faults
- Excessive Oil Temperature
- Steering Problems
- System Pressure Tests: Hydraulic, Transmission, Torque Converter.
Appendices & Reference
- Service Tools (Special John Deere Tools)
- Cross-Sectional Views & Diagrams
- Bolt Torque Charts (Standard & Metric)
- Bearing and Seal Kits Lists
- O-Ring and Gasket Sizes
This manual is structured for sequential, system-by-system repair, moving from general specs to major assemblies, and concluding with integrated diagnostics.