Wacker Neuson ST50 SW32 Track loader Operators Manual
Operator’s Manual (S06-7)
Skid Steer Loader/Compact Track Loader
SW16 / SW17 / SW20 / SW21 / SW24 / SW28 / SW32/ ST28 / ST31 / ST35 / ST40 / ST45 / ST50
Wacker Neuson ST50 Track loader Operator’s Manual
Improper operation of the machine can result in serious injury or death. Before operating this machine, make sure to:Read and understand the Operator’s Manual.Read and understand all labels on the machine.Have training in the safe and proper use of the machine. Follow all applicable laws and regulations that pertain to this machine.
perator’s Manual Information on this Operator’s ManualThe document box for storing the Operator’s Manual is located on the rear of the operator seat.
This Wacker Neuson ST50 SW32 Track loader Operators Manual Operator’s Manual contains important information on how to work safely, correctly and economically with the machine. Therefore, it is intended not only for new personnel, but it also serves as a reference for experienced personnel.
The reliability and the service life of the machine will be increased by following the instructions in the Operator’s Manual.The operator must carefully read and understand the Operator’s Manual before starting up, servicing, or repairing the machine.
This Operator’s Manual will help to familiarize yourself with the machine, thereby enabling you to use it more safely and efficiently.This Operator’s Manual does not include information on attachments.Please contact your dealer if you require more information on the machine or the Operator’s Manual.
Expectations for information in this manual
This Wacker Neuson ST50 SW32 Track loader Operators Manual manual provides information and procedures to safely operate and maintain this Wacker Neuson machine. For your own safety and to reduce the risk of injury, carefully read, understand, and observe all instructions described in this manual.
Wacker Neuson expressly reserves the right to make technical modifi-cations, even without notice, which improve the performance or safety standards of its machines
The information contained in this manual is based on machines manufactured up until the time of publication. Wacker Neuson reserves the right to change any portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson factory-installed components. Your machine may vary depending on the requirements of your specific region.
Machine Description and Intended UseDescriptionThe Wacker Neuson skid steer and compact track loaders are self-propelled work machines.These machines are versatile and powerful helpers for moving earth, gravel, and debris on construction sites and elsewhere. A wide range of attachments allow for numerous different applications of the machines in various environments.
When using these attachments, observe the legal regulations of your country and equip the machine with all the safety equipment required.The main components of the machine are:
In accordance with this designated use, the machine may only be used for moving earth, gravel, coarse gravel or ballast, and rubble. It may also be operated with approved attachments for additional applica-tions. Wacker Neuson ST50 SW32 Track loader Operators Manual
No other applications are designated for the use of the machine. Wacker Neuson will not be liable for damage resulting from use other than mentioned above. The operator alone will bear the risk.
Designated Use includes following the instructions set forth in the Operator’s Manual and following the maintenance schedule.
Wacker Neuson ST50 SW32 Track loader Operators Manual
Machine operation
Continued from the previous page.
- Using a floor jack and jack stands, raise the side of the machine that
needs its track adjusted. - Loosen the screws and swing the cover down.
- Apply grease into the valve with a grease gun.
- Check the track tension again, referencing the table in Checking Track
Tension. If the track tension is still out of specification, repeat steps 3
through 5. - If the track still does not have enough tension after applying grease
again, do not put the machine into operation. Contact a Wacker
Neuson dealer. - Lower the machine to the ground.
- Reinstall the cover.
Reducing track tension - Using a floor jack and jack stands, raise the side of the machine that
needs its track adjusted. - Stop the engine.
- Slowly turn the valve a maximum one revolution counterclockwise
to release the grease into a suitable container.
- The grease flows out of the groove of the valve.
Environment
Use a suitable container to collect fluids and lubricants as they
flow out and dispose of them in an environmentally friendly
manner.
- Tighten the valve until it is snug.
- Check the track tension again, referencing the table in Checking Track
Tension. If the track tension is still out of specification, repeat
procedures for increasing or reducing track tension as needed. - If the track still does not have enough tension after applying grease
again, do not put the machine into operation. Contact a Wacker
Neuson dealer. - Lower the machine to the ground.
- Reinstall the cover.
Wacker Neuson ST50 SW32 Track loader Operators Manual