D6R Series II Caterpillar Service Repair Manual – DS, XL C9 Engine FDT00001-UP
The Caterpillar D6R Series II Service Repair Manual provides detailed service, repair, testing, troubleshooting, and technical information for D6R Series II DS and XL Track-Type Tractors equipped with the C9 engine, serial number FDT00001-UP.
- Format: PDF
Type: Service Manual
Pages: 8881
Size: 374 Mb
No.: FDT00001-UP
Technical Contents Index:
Power Train Electronic Control System
561N, 572R Series II, 572R Pipelayers + D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II, D8R Series II Track-Type Tractors
- Air Inlet Heater Does Not Perform Additional Heating Cycles
- Air Inlet Heater Does Not Turn Off
- Air Inlet Heater Does Not Turn On
- Air Inlet Heater Performs Additional Heating Cycles
- Backup Alarm / Always Off / Always On
- Blade Control Lever Does Not Stay in Float Position
- Calibration / Calibration Operation
- Cat Data Link
- Diagnostic Capabilities / Diagnostic Code List
- Electrical Component and Connector Locations
- Electrical Connector – Inspect
- Electronic Control Module (ECM) – Flash Program / Replace
- Electronic Control Module (Power Train)
- General Information
- Glossary of Electrical Terms
- Indicators
- MID 113 Diagnostic Codes (full CID/FMI list)
- Power Supply Circuit of Electronic Control Module
- Quick Left/Right Turn Does Not Function
- Related Operations of Caterpillar Monitoring System / VIDS
- Relays / Sensors / Solenoid Valves / Switches
- Service Tools
- Speed Sensor – Adjust
- System Operation / System Schematic
- Transmission Does Not Downshift / Upshift
- Using Caterpillar Electronic Technician / Monitoring System
- Warning Operation
- Wiring Harness (Open Circuit / Short Circuit) – Test
AccuGrade Laser System
- Bank Valve (Grade Control) / Calibrate
- Blade Reaction Time – Adjust (Valve Speed)
- CB Fault Codes (CB 1 to CB 36)
- Configuration Menu / Installation Menu / Fault History Menu
- Connector Contact Description
- Counterbalance Valve – Test and Adjust
- Data Link
- Determining Detected Faults (Display / Electronic Service Tool)
- Diagnostic Capabilities / Diagnostic Code List
- Display / Display Icons
- Electric Mast
- Electrical Connector – Inspect / Electrical Power Supply
- Electronic Control Module (ECM)
- EM Fault Codes (EM 1 to EM 31)
- General Information
- Hydraulic System
- Laser Receiver
- Linked Elevation (Dual Mast) – Adjust / Calibrate
- LR Fault Codes
- Menus / Modes of Operation
- MID 114 Diagnostic Codes
- Module – Flash Program / Replace
- Operational Problems
- Service Tools
- System Schematic / System Setup
- Test Control Box Menu / Test Valves Menu
- Wiring Harness (Open Circuit / Short Circuit) – Test
AccuGrade Laser (CD610)
- Bank Valve (Grade Control) / Calibrate
- Blade Reaction Time – Adjust
- CB Fault Codes (including CB 19, CB 21, CB 22, CB 40–63)
- Configuration Menu
- Counterbalance Valve – Test and Adjust
- Data Link
- Determining Detected Faults
- Diagnostic Capabilities / Code List
- Display / Display Icons
- Electrical Connector – Inspect / Power Supply
- EM Fault Codes (including EM 32)
- General Information
- Hydraulic System
- Linked Elevation (Dual Mast) – Adjust / Calibrate
- LR Fault Codes (LR 0 to LR 5 + LR 148)
- Menus / Modes of Operation
- MID 114 Diagnostic Codes
- Module – Flash Program / Replace
- Operational Problems
- Service Tools
- System Schematic / System Setup
- Wiring Harness Tests
AccuGrade GPS
- Angle Sensor – Calibrate
- Avoidance Zone
- Bank Valve (Grade Control) – Calibrate
- Beeper / Blade Wear / Brightness
- Blade Reaction Time – Adjust
- Connector Contact Description
- Counterbalance Valve – Test and Adjust
- Customer Supplied Radio / Data Card / Design Folder
- Display Firmware Upgrade / Settings / Units
- Electrical Connector – Inspect
- General Information / Glossary of Terms
- GPS Accuracy Mode / Guidance Terms
- Increment Switch – Adjustment
- Light Bar – Configure / Scale
- Machine Dimensions / Type – Configure
- Map Recording
- Modes of Operation
- Module – Flash Program / Replace
- Plan View Rotation / Radio Utility
- Receiver Configuration / Firmware Upgrade
- Sensor Firmware Upgrade
- Setup Menu / Software Support Option
- System Components / System Schematic
- Text Items / Vertical Guidance Method
- Wireless Communication
- Wiring Harness Tests
AccuGrade CD700 Grade Control System
- Angle Sensor – Calibrate
- Avoidance Zone / Bank Valve – Calibrate
- Beeper / Blade Reaction Time / Blade Wear / Brightness
- Connector Contact Description
- Counterbalance Valve – Test and Adjust
- Customer Supplied Radio / Data Card / Design Folder
- Display Firmware Upgrade / Language / Registration / Settings / Units
- Electrical Connector – Inspect
- Flashing Messages
- General Information / Glossary of Terms
- GPS Accuracy Mode / GPS Radio Port / Guidance Terms
- Increment Switch / Light Bar – Configure / Scale
- Machine Dimensions / Type – Configure
- Map Recording / Modes of Operation
- Module – Flash Program / Replace
- On-Grade Tolerance / Operator Access
- Plan View Rotation / Radio Utility
- Receiver Configuration / Firmware Upgrade
- Sensor Firmware Upgrade
- Setup Menu / Software Support Option
- System Components / System Schematic
- Text Items / Wireless Communication
- Wiring Harness Tests
- Advanced Tracking System / Base Station / CAN Data Link
- Controls / Determining Detected Faults
- Diagnostic Capabilities / Code List
- Electrical Power Supply
- Hydraulic System / Light Bar
- Machine Position – Display Messages / Machine Radio
- MID 114 Diagnostic Codes
